Perancangan Sistem Kontrol Otomatis Turbin Angin Yaw Direction

Authors

  • Ajat Sudrajat Program Studi Teknik Fisika, Universitas Nasional
  • Fitria Hidayanti Program Studi Teknik Fisika, Universitas Nasional
  • Viktor Vekky Ronald Repi Program Studi Teknik Fisika, Universitas Nasional
  • Derrian Widjayahakim Program Studi Teknik Fisika, Universitas Nasional

DOI:

https://doi.org/10.47313/jig.v23i2.936

Keywords:

sistem kontrol, turbin angin, yaw-direction, horizontal axis wind turbine.

Abstract

Desain turbin angin adalah proses menentukan bentuk dan spesifikasi turbin angin untuk mengekstraksi energi dari angin. Instalasi turbin angin terdiri dari sistem yang diperlukan untuk menangkap energi angin, mengarahkan turbin ke arah angin, mengubah putaran mekanis menjadi tenaga listrik, dan sistem lain untuk memulai, menghentikan, dan mengontrol turbin. Perancangan turbin angin pada penelitian ini, adalah turbin angin yang akan menerima energi angin dari arah yaw (yaw direction). Gerakan menentukan arah dari terbin angin ini dibantu oleh perangkat lunak Lab-View dengan menggunakn kontroler arduino sebagai pengendali arah gerakannya. Perancangan sistem kontrol pergerakan sumbu yaw dari turbin angin dengan bantuan perangkat lunak LabView dan arduino untuk mengendalikan motor yang akan memutar roda gigi yang dihubungkan dengan plat. Pergerakan ini diharapkan dapat menjadi peningkat efisiensi dari turbin angin dalam menerima angin yang datang. Hasil kalibrasi sistem turbin angin dilakukan pada gerakan motor pada arah yaw, dan data putaran potensiometer terhadap tegangan listrik yang diberikan sebagai inputnya.

References

A. Arvirianty, “RI Punya Potensi 978 MW Tenaga Angin, Ini Sebarannya,” CBNC Indonesia, 2018. [Online]. Available: https://www.cnbcindonesia.com/news/20180924102847-4-34413/ri-punya-potensi-978-mw-tenaga-angin-ini-sebarannya.

“Potensi Energi Terbarukan Indonesia,” EPSILOM, 2017. [Online]. Available: https://epsilon.ft.ugm.ac.id/2017/01/16/potensi-energi-terbarukan-indonesia/.

H. Shah, N. Bhattarai, S. Mathew, and C. M. Lim, “Low Reynolds Number Airfoil for Small Horizontal Axis Wind Turbine Blades,” Sustain. Futur. ENERGY 2012 10th SEE FORUM, no. November, pp. 1–7, 2012.

M. G. Kim and P. H. Dalhoff, “Yaw Systems for wind turbines-Overview of concepts, current challenges and design methods,” J. Phys. Conf. Ser., vol. 524, no. 1, pp. 0–10, 2014.

A. L. R. J. F. Manwell , J. G. McGowan, Wind energy explained : theory, design, and application, 2nd ed. John Wiley & Sons Ltd., 2009.

S. Wan, L. Cheng, and X. Sheng, “Effects of Yaw Error on Wind Turbine Running Characteristics Based on the Equivalent Wind Speed Model,” Energies, vol. 8, no. 7, pp. 6286–6301, 2015.

H. M. Nguyen and D. S. Naidu, “Evolution of wind turbine control systems,” Encyclopedia of Life Support System, no. December. 2016.

T. K. Barlas and G. A. M. van Kuik, “Review of state of the art in smart rotor control research for wind turbines,” Prog. Aerosp. Sci., vol. 46, no. 1, pp. 1–27, 2010.

F. Castellani, D. Astolfi, F. Natili, and F. Mari, “The Yawing Behavior of Horizontal-Axis Wind Turbines: A Numerical and Experimental Analysis,” Machines, vol. 7, no. 1, 2019.

R. P. Ruilope, “Modelling and Control of Stepper Motors for High Accuracy Positioning Systems Used in Radioactive Environments,” PhD Thesis, Univ. Politécnica Madrid, 2014.

F. Bu, W. Huang, Y. Hu, Y. Xu, K. Shi, and Q. Wang, “Study and implementation of a control algorithm for wind turbine yaw control system,” in 2009 World Non-Grid-Connected Wind Power and Energy Conference, 2009, pp. 1–5.

M. R. Djalal, A. Imran, and H. Setiadi, “Desain Sistem Kontrol Pitch Angle Wind Turbine Horizontal Axis Menggunakan Firefly Algorithm,” J. Tek. Elektro, vol. 9, no. 1, pp. 1–6, 2017.

S. Theodoropoulos, D. Kandris, M. Samarakou, and G. Koulouras, “Fuzzy Regulator Design for Wind Turbine Yaw Control,” TheScientificWorldJournal, vol. 2014. School of Engineering and Physical Sciences, Heriot Watt University, Edinburgh EH14 1AS, UK., p. 516394, 2014.

S. P. Venkatesan, J. K. Soni, and A. Burugpalli, “Increasing efficiency of a wind turbine using a convergent nozzle in combination with a flanged diffuser,” Int. J. Appl. Eng. Res., vol. 10, no. 11, pp. 10234–10240, 2015.

A. K. S. Parikshit Bharpte, Sumit Saindre, Lalit Mahajan, “Electricity Generation by Maglev Windmill,” Int. Res. J. Eng. Technol., vol. 11, no. 5, pp. 1104–1109, 2018.

Downloads

Published

2020-11-26

Issue

Vol. 23 No. 2 (2020): Volume 23 Edisi 2 Tahun 2020

Section

Articles

License

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).