Rancang Bangun Mesin Poles Piringan Tunggal (Single Disc) Untuk Proses Metalografi

Article Sidebar

PDF
Published: Jun 21, 2021
DOI: https://doi.org/10.47313/jig.v24i1.1070

Main Article Content

Ferry Budhi Susetyo
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Negeri Jakarta, 13220
Muhamad Muslih
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Negeri Jakarta, 13220
Muhamad Agil Febrianto
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Negeri Jakarta, 13220
Basori Basori
Program Studi Teknik Mesin, Fakultas Teknik dan Sains, Universitas Nasional

Abstract

A polishing machine for the metallographic process is the equipment used to carry out surface preparations. The smooth surface is expected so that after etching it can be seen the micro or macrostructure of a material being studied with the aid of a microscope. In this research, we design and manufacture polishing machines. The main materials used in the process of designing this polishing machine are an electric motor (AC), carbon steel, cables, contactors, stainless steel plates, pushbuttons, emergency buttons, potentiometers, v belts, pulleys, bearings, hoses, and shafts. This method of the research process begins with calculating the diameter of the follower pulley, then continues with size planning, drawing work, making simple electrical wiring drawings, manufacturing components, and assembling and testing. This polishing machine for the metallographic process has been designed as a disk rotating speed of 600 rpm, an electric motor of 135W with a voltage of 220V, and also has a plumbing system. From the test results of polishing machine for metallography, the desired polishing results were obtained.

Article Details

How to Cite
Susetyo, F. B., Muslih, M., Febrianto, M. A., & Basori, B. (2021). Rancang Bangun Mesin Poles Piringan Tunggal (Single Disc) Untuk Proses Metalografi. Jurnal Ilmiah Giga, 24(1), 17–22. https://doi.org/10.47313/jig.v24i1.1070
Issue
Vol. 24 No. 1 (2021): Volume 24 Edisi 1 Tahun 2021
Section
Articles

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

References

A. Suhandi and L. Anggraini, “Analisa Struktur Mikro dan Sifat Mekanik Pada Copper-Iron Melalui Proses Mechanical Milling dan Continuous Sintering,” J. Mech. Eng. Mechatronics, vol. 2, no. 2, pp. 88–99, 2017.

M. Mandala and E. S. Siradj, “Struktur Mikro Dan Sifat Mekanis Aluminium (Al-Si) Pada Proses Pengecoran Menggunakan Cetakan Logam, Cetakan Pasir Dan Cetakan Castable,” Poros, vol. 14, no. 2, pp. 88–98, 2016.

S. Mahardika, “Analisa Rekayasa Sifat Mekanik Baja Aisi 4140 Dengan Variasi Suhu Tempering Untuk Meningkatkan Keuletan Dan Kekerasan Material,” J. Mekanova Mek. Inov. dan Teknol., vol. 6, no. 1, pp. 64–69, 2020.

Windarta and D. Setiawan, “Optimasi Balancing Putaran Pada Mesin Poles Piringan Ganda Untuk Pengujian Metalografi,” Semin. Nas. Sains dan Teknol. 2018 1 Fak. Tek. Univ. Muhammadiyah Jakarta, vol. 1, pp. 1–8, 2018.

M. I. Almadani and Rudi Siswanto, “Proses Manufaktur Mesin Poles Dan Ampelas Untuk Proses Metalografi,” Rotary, vol. 2, no. 1, pp. 15–22, 2020.

G. I. Sukmana and A. H. A. Rasyid, “Redesain Mesin Grinding Dan Polish Semi Otomatis,” J. Rekayasa Mesin, vol. 5, no. 1, pp. 51–58, 2018.

V. W. Gandoria, V. V. R. Repi, and A. Wibowo, “Rancang Bangun Pengamat Parameter Cuaca Menggunakan Komunikasi Nir Kabel,” J. Ilm. GIGA, vol. 22, no. 1, pp. 14–21, 2019.

A. Supriyadi, V. Vekky, R. Repi, and F. Hidayanti, “Rancang Bangun Sistem Pencampuran Warna Tekstil Otomatis dengan Parameter Volume Fluida pewarna,” J. Ilm. GIGA, vol. 21, no. 2, pp. 58–68, 2018.

F. B. Susetyo, I. W. Sugita, B. Basori, M. N. Rifqi, R. Wardiana, and J. Prasetyo, “Rancang Bangun Rak Penetas Telur Otomatis Pada Mesin Tetas Bertenaga Hybrid,” J. Ilm. Giga, vol. 23, no. 2, pp. 69–75, 2020.

I. Syinnaqof and D. Riandadari, “Rancang Bangun Mesin Pengaduk Dodol Dan Jenang,” J. Rekayasa Mesin, vol. 4, no. 2, pp. 83–88, 2017.